澳门威斯尼斯人网站-首页 在线留言 收藏本站 网站地图 联系连讯达
(澳门威斯尼斯人网站)手机版
当前位置:澳门威斯尼斯人网站 » 公司动态 » fluke DSX-5000中TCL与ELTCTL是什么意思?测试不过怎么办?

fluke DSX-5000中TCL与ELTCTL是什么意思?测试不过怎么办?

文章出处:深圳市连讯达电子技术开发有限公司 人气:-发表时间:2014-09-20 10:45:00

深圳市连讯达电子技术开发有限公司网络部工程师为大家介绍FLUKE测速设备中TCL与ELTCTL两个参数的意思。(PS:这是DTX-1800里面没有的参数)


transverse conversion loss  TCL 横向变换损耗

transverse conversion transfer loss  TCTL 横变换转移损耗

TCL (Transverse Conversion Loss) – DSX CableAnalyzer TCL is one of two balance measurements found in ANSI/TIA-568-C.2, ANSI/TIA-1005 and ISO/IEC 11801:2010. The other is ELTCTL.



The measurement is made by injecting a differential mode signal (DM) into a twisted pair, then measuring the common mode signal (CM) returned on that same twisted pair. The smaller the CM signal returned, the better the TCL measurement (balance).

 

翻译:测量是通过向双绞线注入差模信号(DM),然后测量同一对双绞线返回的共模信号(CM)。CM信号返回的越少,TCL参数就会越好,越平衡。



If it looks similar to a Return Loss measurement, you're right. Except a Return Loss measurement is made by injecting a DM signal into the pair and measuring the DM signal returned. Here we are measuring the CM signal returned which is TCL.


翻译:如果你觉得它像是回波损耗的测试,那你就说对了。回波损耗测试是通过向双绞线注入DM(差模信号)然后测试返回的DM信号,然而TCL是测试CM信号。


Field test requirements for ANSI/TIA-568-C.2 are deferred to ANSI/TIA-1152. At this time, TCL is not a field test requirement because until the DSX CableAnalyzer came along, no field test equipment vendor could perform a TCL field test. It is anticipated that other test equipment vendors will eventually offer TCL field measurements too. Field testers are normally capable of DM measurements only – the DSX CableAnalyzer is capable of both DM and CM measurements, hence its ability to measure TCL and ELTCTL.


翻译:对于ANSI/TIA-568-C.2现场测试要求直到ANSI/TIA-1152标准。在那个时候,TCL并不是一个现场测试的要求,因为没有现场测试设备供应商可以执行TCL现场测试,直到DSX-5000电缆认证分析仪的诞生。预计其他品牌测试设备厂家最终也将提供TCL现场测量。现场测试人员通常仅能DM测量 – 对DSX-5000电缆认证分析仪能够既DM和CM的测量,因此其有测量TCL与ELTCTL的能力。


If you wish to add TCL and ELTCTL to your standard Category 5e, 6, 6A or Class D, E or EA test, select your test limit under the folder in DSX called Balance Measurements and look for your test limit with a suffix of (+TCL):


翻译:如果需要对于Cat5e,Cat6,Cat 6A测试TCL和ELTCTL参数,你只需要再DSX-5000 的文件夹下面找到+TCL的后缀就可以了。


This will add ≈ 6.6 seconds to your AUTOTEST time.

TCL测试将增加6.6秒测试时间。


The suffix of (+TCL) indicates a standard ANSI/TIA or ISO/IEC test with the addition of TCL and ELTCTLmeasurements. ANSI/TIA-568-C.2 and ISO/IEC 11801:2010 only provide test limits for Channel measurements at this time. If you select a Perm. Link test limit, the TCL and ELTCTL measurements will be performed, but there will be no PASS/FAIL criteria applied. You will also see the Industrial Ethernet standards TIA 1005 with the different E1, E2 and E3 environmental TCL and ELTCTL limits.


翻译:有(+TCL)后缀的预示着ANSI/TIA或者ISO/IEC测试有这个规格。 目前ANSI/TIA-568-C.2 and ISO/IEC 11801:2010 仅仅提供信道测试的极限值,如果选择永久链路测试,TCL和ELTCTL也会被执行,但是不会有通过/失败的标准。同样你也会看到工业以太网标准TIA 1005 ,E1,E2,E3的标准的限制。


In the example below from a DSX-5000 CableAnalyzer, a Category 6A Channel was tested. With a margin of 5.4 dB (6 dB is a factor of 2), you can feel confident that this link will perform well, even in a noisy environment.



翻译:从下面DSX-5000的例子中可以看到,Cat 6A通道测试有5.4db的余量,你就不用担心了,因为这条链路表现非常好。即使在有噪音的环境下。


此文关键字:fluke,福禄克,澳门威斯尼斯人网站,光纤测试仪,网线测试仪,万用表,威斯尼斯人娛乐城v29,深圳连讯达,深圳市连讯达电子技术开发有限公司